洛阳通风管道知名加工厂

闸门安装调试

Gate installation and debugging

1、 安装前，要首先检查竖框与横框之间、闸板与闸板之间（指多块闸板组合的闸门）的连接螺丝，是否在运输装卸中引起松动，它们的接茬是否错牙，要调整成一个平面，检查闸板与闸槽的间隙，保证闸槽与闸板的间隙不大于0.08mm，如有间隙可以调节闭紧装置。上紧各连接螺栓。 2、 安装时闸门整体竖入预留槽，在两边立框的下面垫上调整垫（严禁垫下横梁），两立框用手动葫芦和斜拉立稳，将闸门找直找平，各地脚孔内串上地脚螺栓，调节好闸门的位置，支好模板进行二期浇注。 3、 浇注混凝土时，流进闸板、闸框、斜铁、挡板间的灰浆应彻底清除，以防止灰浆凝固后影响闸门启闭。 4、 清除加固物。闸门出厂前，为使闸板、闸框贴合紧凑，安装后减少间隙，2m以上的闸门在上下框上安装了4-6个紧闭装置压铁，注意在间隙调整后，闭紧压铁拆除，以便闸门启闭。

1, before installation, we should first check the connecting screw between the vertical frame and the cross frame, between the gate and the gate (the gate of the multiple sluice), whether it is loose in the handling of the transport, whether their succession is wrong, and the gap between the sluice and the sluice should be adjusted to ensure that the gap between the gate and the gate is not greater than that of the gate. 0.08mm, if there is a gap, the closing device can be adjusted. Tighten the connecting bolts. 2, at the time of installation, the gate is integrated into the reserved slot, and the cushion is adjusted on the bottom of the two sides of the frame (strictly prohibit the cross beam). The two erect frames use manual gourd and slanted to stand steadily. The gate is straight and leveled, the foot bolts on the foot holes in various places are used to adjust the position of the gate, and a good template is put into the two stage pouring. 3, when pouring concrete, the mortar flowing into the gate, gate frame, diagonal iron and baffle should be thoroughly removed, so as to prevent the mortar from solidifying and affect the opening and closing of the gate. 4. Remove the reinforcement. Before the gate is out of the factory, in order to make the gate and sluice frame close to compact and reduce the gap after installation, 4-6 locking devices are installed on the upper and lower frames of 2m, and attention is paid to the closing of the gate after the clearance adjustment.

       （二）闸门使用保养

(two) gate maintenance

1、闸门应注意闸板的上、下极限位置，不能超限，以免损坏闸门或启闭机。 2、闸门在起闭过程中如有异常情况应立即停止使用，及时检查修理。 3、闸门在关闭时距闸底10公分处，暂停2分钟，让激流冲净底门槽内杂物，然后再将闸门关闭。4、在闸门长期闭合前应急时清除闸板及闸框上的污物，在清除完之后重新涂上新油以防锈蚀影响以后的启闭。

1, gate should pay attention to the upper and lower limit of gate, and not exceed the limit, so as not to damage gate or hoist. 2, if there is any abnormal condition in the process of lifting and closing, the gate should be stopped immediately, and timely checked and repaired. 3, when the gate is closed, it is 10 centimeters away from the bottom of the lock, and pause for 2 minutes. Let the rushing stream clean the debris in the bottom door slot, then close the gate. 4, clear the sluice and sluice on the emergency gate before emergency closure. After the cleaning is finished, new oil will be applied again to prevent rust from affecting the opening and closing.